Meteorological Towers
M-10M
10-meter freestanding meteorological tower designed
for small, lightweight antennas, maximum of 35lbs.
of dead weight & 3 sq.ft. of surface area. Aluminum
MET tower is ideal for wind speed and direction
equipment, sensors, and light antennas. Tilt-base
designed to be cemented directly into customer’s
concrete pad. For temporary guyed installation,
tower offered with a hinged base with a temporary
mounting plate, guy wire ears and a guy kit.
Aluminum tower consists
of 3-sided, 10-meter equilateral triangle design
constructed of tubular legs of 6061-T6 aluminum.
The three 10 ft. sections are sleeved for quick
installation. Tower is durable and easy to use.
The freestanding tower is rated for 110 mph wind
speed properly installed. Towers are complete
with base and 1” Schedule 40 pipe (1.315"
OD) x 5’ long aluminum mast.
Model M-10M-PT freestanding tower consists of
three 10’ aluminum sections with M-787 tilt
base. Tilt base is precast directly into concrete
pad. Model
M-10M-TEM tower for temporary installation consists
of three 10’ aluminum sections with M-818
plate tilt base. Guying required for roof or
concrete slab installation. Includes Guy Kit
#1-30BG.
Model M-10M-PTGIN tower consists
of three 10’ aluminum sections plus gin
pole to facilitate the tilting of tower. Tilt
base M-787 is precast directly into concrete
pad.
10M
FOLD-OVER ALUMINUM TOWER:
FOT-10 10-meter aluminum
tower designed for small, lightweight antennas
or equipment . Specifically
designed to elevate air-sampling equipment.
The tower tilts-over easily to allow for rapid
collection of samples. Tower consists of two “B” sections:
lower section 17 ft. and upper section 25
ft. The upper section is hinged at top of
the lower section to fold-over. Tower is complete
with a 2” dia. x 1/8”
wall x 4’-9” long mast and fixed
base. Lower section must be guyed or building
bracketed at a minimum of six feet.
FOT-10-BW 10-meter aluminum
tower consists of two “B” sections:
lower section 17 ft. and upper section 25 ft.
The upper section is hinged at the top of the
lower section to fold-over. Tower is complete
with a 2” dia. x 1/8” wall x 4’-9”
long mast, fixed base and brake
winch. Lower
section must be guyed or building bracketed
at a minimum of six feet.
10M CRANKUP
ALUMINUM TOWERS:
Model T-135 and T-35H 35 ft. aluminum telescoping
towers. The 35-foot telescoping towers nest
to approximately 12 ft. These towers feature
a tilt base and one person can “walk-down”
a light duty tower. Crankup towers can be telescoped
to desired height. The towers are manufactured
from 6063 T82 and 6061 T6 aluminum and are complete
with a tilt-base, building bracket and mast.
See TELESCOPING
TOWERS for details.
MOBILE,
PORTABLE TOWERS:
Trailer tower units and vehicle-mounted units
are ideal for mobile operations. The transportable
tower units are designed for rapid setup and
easy operation in the field.
TRAILER
TOWERS WITH ALUMINUM TELESCOPING TOWERS:
Telescoping 10M towers also combined with Trailers
to provide portable units. TM 12/T-BD-135 and
TM 12/T-BD-35H are Single axle galvanized trailers
with 35’ aluminum crankup towers.
See TRAILER
TOWERS
VEHICLE
MOUNTED ALUMINUM TELESCOPING TOWERS:
Vehicle-mounted aluminum telescoping towers
designed for mounting on a customer’s
vehicle.
BD-110M and BD-10MHD are 10M
crankup towers complete with track and carriage.
See VEHICLE
MOUNTED ALUMINUM TELESCOPING TOWERS
CAUTION:
Take care to avoid any contact with overhead
power-lines when raising, installing, or lowering
your tower. Click here for full WARNING.
back to top |
